![]() Printing on Retail POS with Star Perform a test print From the new Print Queue window, select the Print Test checkbox and click Apply. Click on your Star printer and its dynamic IP address and click Print Queue.ĥ. From the new User Account Control window, click Discovery.Ĥ. Open the LAN & Bluetooth Setup Tool, and search for LAN.ģ. Deselect the Launch Star Cloud Services Web site and click Finish once you are done.ġ. Follow the setup steps to install the printer driver on your computer.ĩ. In the new TSP100 futurePRNT window, click Installation > I Accept.Ĩ. From the tsp100 folder, double-click Autorun.ħ. From the Compressed (Zipped) Folder windows, click Extract All > Extract.Ħ. From the new folder, double-click Autorun.ĥ. Go to the Downloads folder on your PC and double-click the downloaded file to expand.Ĥ. Click TSP100 futurePRNT Software Lite to download the latest driver.ģ. Installing your printer driver on your computerĢ. This is your printer's new dynamic IP address. Under the Current IP Parameters Status, take note of the IP Address. Your printer will automatically make a printout. From the left menu, click the Save section and navigate to Save > Configuration printing > Restart Device. Security Key: your Wi-Fi network password.ġ0.Select Infrastructure Mode and enter the following: Click Cancel, to close the new security window.ĩ. Once your Network Configurations and Current IP Parameters Status receipts print successfully, release the Feed button.ħ. While still holding the Feed button, turn your printer back on.Ĥ. Press and hold the Feed button on the front of the printer while the printer is turned off.ģ. Switch your printer off using the power switch.Ģ. Printing your Network Configuration and Current IP Parametersġ. To achieve an AP network connection, the printer should be connected to your router using an ethernet cable. This involves printing your network configuration and current IP Parameters and setting your wireless LAN settings. Retry steps 1 and 2 again to ensure the printer is paired to the network. If the IP address on the receipt says "NONE" or "0.0.0.0", the printer is not connected to the internet. This will be your printer's new dynamic IP address. Under Current IP Parameters, make a note of the IP Address. The Ready light on the printer will now be solid and your Network Configuration and Current IP Parameters Status will print out automatically.Ĥ. This will establish a connection between your printer and your router. Steps 1 and 2 have to be done within 30 seconds of each other. The usage procedure of the access point or router will vary according to the device. Press and hold the red Pair button on the back of your printer until the blue light on the front of your printer starts blinking.Ģ. However, if your router does not support WPS, use the steps under Connect by AP network mode instead.ġ. The simplest way to connect your printer is by a WPS. You are now ready to connect your printer to your wireless network. ![]() Turn your printer on and wait for the blue light to stop blinking. Connect the Star TSP100/TSP100III to a power source using the provided power cableĢ. Using the dedicated app (TSP100III Utility Mac/iPad) will help you set your product up easily.ġ. This is a specialized cash drawer cable that is similar looking to an ethernet cable but is smaller on one end. ![]() You may also wish to set up your cash drawer at the same time, to do this you'll need an RJ12 cable. To load your receipt roll open the latch on the top right of the printer, place the roll inside, and pull some of the paper through before closing the lid. You will need a power cable for the printer. ![]() To set up your receipt printer with your PC, Mac, or iPad, you'll first need to make sure you have all the peripherals needed. Select the tab for your device platform (Mac, Windows PC, or iPad) and follow the provided steps.įor more information on your TSP 100III Wireless Printer, refer to Star's Online Manual. This guide provides step-by-step instructions to connect your Star TSP100III wirelessly to your internet router and provide wireless receipt printing. To fix this, ensure your device's Bluetooth and Local Network Permissions are enabled in Settings > Lightspeed Retail POS (X). If declined, this will cause your printer to no longer function. Important: Updating to iOS 14+ on iPad will prompt you to grant the Retail POS app permissions to access Bluetooth and Local Network settings on your iPad. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |